Engineered or solid wood?
Solid wood is one piece of timber all the way through. It can be sanded and refinished many times, but it reacts more to changes in humidity, so it suits stable rooms without underfloor heating.
Engineered wood has a top layer of real wood, the wear layer, bonded to a stable core. It moves less, which makes it the usual choice over underfloor heating, on concrete floors and in large open rooms. How many times it can be sanded depends on the thickness of the wear layer.
| Engineered | Solid | |
|---|---|---|
| Surface | Real wood | Real wood throughout |
| Stability | More stable | Moves more with humidity |
| Underfloor heating | Usually suitable; check the product | Often not recommended |
| Sanding | Depends on the wear layer | Many times over its life |
| Fitting | Floated, glued or nailed | Usually glued or nailed |
Herringbone, chevron or plank?
Herringbone uses rectangular blocks laid at right angles in a staggered zigzag. It's classic, and full of movement.
Chevron blocks are cut at an angle at each end, so the points meet in one clean, continuous line. It reads as more formal and architectural.
Planks are calmer and quicker to lay. Wider boards suit large and open-plan rooms.
Patterns cost more to fit than planks: every block is set out, cut and glued, and the layout starts from the centre of the room so the pattern sits square to the walls. That set-out is what makes a pattern look right from every doorway.
Oiled or lacquered?
Oil soaks into the wood for a natural, matt look. Scratches and worn patches can be repaired locally, but it needs re-oiling from time to time.
Lacquer forms a hard film on the surface. It resists spills and wear and needs less upkeep, but damage usually means sanding and recoating a whole area.
Matt lacquers now look close to oil. For busy kitchens, children and pets, lacquer is often the easier life.
What's underneath matters most
Most problems with wood floors, from gaps and cupping to creaks and lifting, start with the base. Before we lay a floor we check three things:
- Moisture. Wood flooring guidance asks for sand and cement screeds below 75% relative humidity for floating floors and below 65% for glued floors. Timber subfloors should be below about 14% moisture content.
- Flatness. A common benchmark is no more than a 3 mm gap under a two-metre straightedge. Anything worse is levelled first.
- Ventilation. Suspended timber floors need air moving underneath, usually through air bricks in the outside walls.
Once laid, wood is happiest at around 45 to 65% relative humidity and 15 to 25°C. In dry winter weather small gaps can open between boards; they close again as humidity returns.
Underfloor heating
- Choose a floor that's approved for underfloor heating. Engineered boards usually are; check the maker's instructions.
- The system should be commissioned, tested and run before the floor goes down.
- Keep the floor surface at 27°C or below, and change the temperature gradually, a few degrees a day.
- Choose an underlay made for underfloor heating. Thick, insulating underlays and big rugs slow the heat getting into the room.
Tiles and stone conduct heat well and pair naturally with underfloor heating. Wood works well too, with the right product and care with temperatures.
Wood, tile or something else?
| Room | Good choices | Think twice about |
|---|---|---|
| Living rooms and bedrooms | Engineered or solid wood, herringbone, chevron or plank | Very soft or pale finishes in busy rooms |
| Kitchens | Engineered wood with a tough finish, porcelain, stone | Solid wood next to sinks and dishwashers |
| Bathrooms | Porcelain and stone | Wood flooring |
| Halls | Porcelain, stone, engineered wood with mats at the door | Finishes that show grit and scratches |
| Over underfloor heating | Tiles, stone, engineered wood | Solid wood, unless the maker approves it |
| Apartments | Any floor with an approved acoustic underlay | A hard floor fitted without checking the lease |
Apartments: check before you buy
Floors between apartments must resist impact sound under Part E of the Building Regulations, and many management companies require a specific acoustic underlay or performance before a hard floor goes down. Ask for the rules in writing, and choose the underlay with the floor. Our guide to a quieter home explains why.
Looking after a wood floor
- Use mats at the doors. Grit is what scratches floors.
- Put felt pads under chairs and furniture.
- Clean with a damp, not wet, mop, and a cleaner made for your finish.
- Keep humidity in the comfortable range, especially with the heating on.
- Re-oil, or maintain the lacquer, as the maker recommends.
Questions
- Is engineered wood real wood?
- Yes. The surface is a layer of real wood, bonded to a stable core. It looks and feels like solid wood.
- Can I have herringbone with underfloor heating?
- Yes, using engineered blocks approved for underfloor heating, fully bonded, with the floor surface kept at 27°C or below.
- How long does a new screed take to dry?
- It depends on its thickness, the mix, the weather and ventilation, and a thick screed can take months. We test it before laying rather than guess.
- Can I have a wood floor in the kitchen?
- Yes, with care: engineered boards with a durable finish, spills wiped up promptly, and a neat seal where the floor meets the units.
Sources
- Wood Flooring Association: general installation guidelineswfa.uk.net
- Wood Flooring Association: engineered design installation guidelineswfa.uk.net
- Wood Flooring Association: engineered design glued installation guidelineswfa.uk.net
- Wood Flooring Association: Parquet installation guidelineswfa.uk.net
- Havwoods: Engineered wood flooring over underfloor heatingres.cloudinary.com
- Engineers Ireland: sound insulation and the Building Regulationsengineersireland.ie
This guide is general information, not legal, financial or professional advice. Grant amounts, rules and regulations change, so check the sources above or ask a qualified professional before you rely on them. Last reviewed 19 November 2026.